Friday, June 23, 2023

Service Manual | PDF | Power Inverter | Power Supply. Eaton 9130 manual

Looking for:

Eaton 9130 manual 













































    ❿  

User manual Eaton RM 2U (English - pages). Eaton 9130 manual



  Table 7. However, Eaton recommends that the batteries charge for 48 hours after long-term storage. Do not dispose of the battery or batteries in a fire.❿    

 

Eaton 9130 manual - Document Information



   

Select the proper holes in the rack for positioning the UPS in the rack see Figure 5. The rails occupy four positions on the front and rear of the rack. Secure one rail assembly to the front of the rack with one M6 16 pan-head screw and one M6 cage nut. Using two M6 cage nuts and two M6 16 pan-head screws, attach the rail assembly to the rear of the rack.

M6 Cage Nuts 6 places. Tighten adjustment M6 16 Pan-Head screws after rail attachment Screws 6 places 3 places each rail. Front of Rack. Tighten the three adjustment screws in the middle of each rail assembly. If installing optional cabinets, repeat Step 1 through Step 6 for each rail kit. Place the UPS on a flat, stable surface with the front of the cabinet facing you. Align the mounting brackets with the screw holes on each side of the UPS and secure with the supplied M4 8 flat-head screws see Figure 6.

Choose the position that meets your configuration needs. Mounting Bracket. M4 8 Flat-Head Screws 4 places. Figure 6. If installing optional cabinets, repeat Steps 8 and 9 for each cabinet.

Secure the front of the UPS to the rack using two M6 16 pan-head screws and two M6 cage nuts on each side see Figure 7. Install the bottom screw on each side through the bottom hole of the mounting bracket and the bottom hole of the rail.

M6 Cage Nuts 4 places. M6 16 Pan-Head Screws 4 places. Figure 7. Securing the Front of the Cabinet. Insert a rear stop bracket through the inside of each rail behind the UPS.

Rotate each bracket and slide the bracket until it fits tightly against the UPS's rear panel. Secure each bracket to the UPS with one M3 8 pan-head screw.

See Figure 8. See Figure 9. To remove the cover, remove and retain the two screws on the right side of the cover. Grasp the top and bottom of the cover and slide the cover to the right. Do not pull on the cable or disconnect it. NOTE Leave ribbon cable connected. Figure 9. This is normal and will not harm personnel. Connect the cables quickly and firmly. Up to VA models. Unclip the top rightmost white connector from the battery panel and move it to the left to connect to the white connector at the top left.

Connect red to red, and black to black. Press the two parts tightly together to ensure a proper connection. Clip the wires of the rightmost connector to the battery panel in its new position. To replace the cover, verify that the ribbon cable is protected and if EBMs are installed the EBM cable is routed through the knockout on the bottom of the cover. Slide the cover to the left until it aligns with the left front cover. Reinstall the two screws on the right side of the right front cover.

If you are installing power management software, connect your computer to one of the communication ports or optional connectivity card see page For the communication ports, use an appropriate cable not supplied. If your rack has conductors for grounding or bonding of ungrounded metal parts, connect the ground cable not supplied to the ground bonding screw. Figure Grasp the sides of the cover and slide the cover to the left and then away from the cabinet.

See Figure 12 for the location of the top EBM cable knockout. See Figure 12 for the location of the EBM cable knockouts.

Plug the EBM cable s into the battery connector s as shown in Figure Connect red to red, black to black, and green to green. All models. Repeat for any additional EBMs. Verify that the EBM connections are tight and that adequate bend radius and strain relief exist for each cable.

To replace the cover, verify that the EBM cables are routed through the EBM cover knockouts, then slide the cover from the left to the right until it connects with the cover hook near the left side of the EBM cabinet.

Reinstall the two screws on the right side of the front cover. For reference, see Figure 12 on page Verify that all wiring connecting the UPS and EBM s is installed behind the front covers and is inaccessible to users. Place the UPS on a flat, stable surface in its final location. If installing additional cabinets, place them next to the UPS in their final location. To remove the cover, push down on the top of the cover and pull the cover toward you to unclip it from the cabinet.

Connect the white connectors together, connecting red to red, and black to black. Place the battery connector between the screw mounts. Reinstall the two screws to hold the connector in place. To replace the cover, verify that the ribbon cable is protected, then insert the clips on the back of the cover into the cabinet and push firmly to snap the cover into place. On the rear of the UPS, remove the cable retention clip covering the battery connector. Retain the clip and screws.

See Figure Installations with one EBM only. Remove the cable retention clip covering the right for — VA models or upper for — VA models battery connector. Installations with more than one EBM. Do not remove the clip from the second battery connector on the last EBM.

Retain the clips and screws. For each cable retention clip removed, rotate the clip and install it under each EBM cable connection using the retained screws. Remove cable retention clip. Plug in EBM cable. Rotate clip. Reinstall cable retention clip. Plug the equipment to be protected into the UPS, but do not turn on the protected equipment. Models without an attached power cord. Press the button on the UPS front panel for at least one second.

Check the UPS front panel display for active alarms or notices. Resolve any active alarms before continuing. If the indicator is on, do not proceed until all alarms are clear. Check the UPS status from the front panel to view the active alarms. Correct the alarms and restart if necessary. Verify that the indicator illuminates solid, indicating that the UPS is operating normally and any loads are powered. NOTE Eaton recommends setting the date and time. NOTE At initial startup, the UPS sets system frequency according to input line frequency input frequency auto-sensing is enabled by default.

After initial startup, auto-sensing is disabled until manually re-enabled by output frequency setting. NOTE At initial startup, input voltage auto-sensing is disabled by default.

When manually enabled by output voltage setting, at the next AC startup the UPS sets output voltage according to input line voltage. After the subsequent startup, auto-sensing is disabled until manually re-enabled by output voltage setting. Activate the external REPO switch. Verify the status change on the UPS display. However, Eaton recommends that the batteries charge for 48 hours after installation or long-term storage.

If optional EBMs are installed, see the recharge times listed in Table 25 on page Keep your UPS firmware updated. This chapter contains information on how to use the Eaton , including front panel operation, operating modes, UPS startup and shutdown, transferring the UPS between modes, retrieving the Event Log, setting the power strategy, and configuring bypass settings, load segments, and battery settings. It provides useful information about the UPS itself, load status, events, measurements, and settings see Figure Power On Indicator green.

On Battery Indicator yellow. Bypass Indicator yellow. Alarm Indicator red esc. The button has no effect on equipment connected to the UPS. Changing the Language Press and hold the first button on the left for approximately three seconds to select the language menu. This action is possible from any LCD menu screen.

Display Functions As the default or after 15 minutes of inactivity, the LCD displays the start screen. The backlit LCD automatically dims after 15 minutes of inactivity. Press any button to restore the screen.

Press any button to activate the menu options. Use the two middle buttons and to scroll through the menu structure. Press the Enter button to select an option. Press the ESC button to cancel or return to the previous menu. Table 2. Service Settings This menu is password-protected. User Settings The following table displays the options that can be changed by the user. Table 3. If After Delay, transfer occurs according to Table 19 on page Remote Shutdown Delay [No Delay] [1s] [2s] On Battery Notice Delay [0] [1s] [2s] Site Wiring Fault Alarm [Enabled] [Disabled] Enabled An active site wiring fault alarm prevents startup or, if operating, forces operation to Battery mode and disables bypass.

The UPS monitors and charges the batteries as needed and provides filtered power protection to your equipment. The UPS may at times silently implement a High Alert mode, usually when incoming utility conditions are unfavorable.

In High Alert mode, the UPS disables the battery support test to ensure maximum capacity from the batteries if needed. Optional High Efficiency and Energy Saving settings minimize heat contribution to the rack environment.

Battery Mode When the UPS is operating during a power outage, the alarm beeps once every five seconds and the indicator illuminates solid. When the utility power returns, the UPS transfers to Normal mode operation while the battery recharges. If battery capacity becomes low while in Battery mode, the indicator flashes slowly and the audible alarm beeps once every second. This warning is approximate, and the actual time to shutdown may vary significantly. See Table 23 on page 88 for estimated runtimes.

Battery mode is not available and your equipment is not protected; however, the utility power continues to be passively filtered by the UPS. The indicator illuminates. The UPS remains in Bypass mode for at least 5 seconds if the bypass source remains acceptable. If three transfers to Bypass occur within 10 minutes for any reason other than user command, the UPS locks in Bypass for 1 hour or until any control button is pressed.

S The UPS detects an internal failure. S The UPS has an overtemperature condition. The UPS remains on to alarm the fault. The indicator is off, indicating that power is not available to your equipment. The battery recharges when necessary, and the communication bay is powered. If utility fails and output turns off due to drained batteries or UPS internal failure, the UPS alarms in Standby mode and powers the communication bay for 1 hour 30 minutes or until battery voltage drops below 1.

If utility fails while the UPS is in Standby mode, the logic power supply turns off in approximately 10 seconds. If the UPS is waiting on commands and utility fails, unit and logic power turn off in approximately 30 seconds. Press the ESC button until the start screen appears. NOTE Battery start can be disabled.

The indicator illuminates solid. The UPS supplies power to your equipment. The UPS then transfers to Standby mode, and the indicator turns off. From Bypass to Normal Mode. Scroll through the listed events. To retrieve the Event Log through the serial port:. The UPS returns a header containing the UPS identification UPS type, part number, and serial number , firmware version, and the current date and time, followed by the event history. Use the connected communication device to view or print the information.

The indicator illuminates when the UPS transfers to Bypass. Transfer to Bypass When Overload. The default forces a transfer to Bypass when any overload condition occurs. You can configure the setting for a delayed transfer, with the amount of delay determined by the amount of overload, as shown in Table 19 on page Bypass Voltage Low Limit.

You can configure the setting for another percentage of nominal. Bypass Voltage High Limit. Qualify Bypass. Synchronization Window. When the Bypass frequency is more than the set value, the UPS goes to nominal frequency. Unsynchronized Transfers. The default allows an unsynchronized transfer to Bypass. You can configure the setting to not allow such transfers. For example, during a power outage, you can keep key pieces of equipment running while you turn off other equipment.

This feature allows you to save battery power. To control the load segments with power management software, see your power management software manual for details refer to the Software Suite CD or www. To control the load segments through the display:. Use the or buttons to select the number of battery strings according to your UPS configuration:.

Running Automatic Battery Tests Automatic battery tests run approximately every 30 days, unless disabled. During the test, the UPS transfers to Battery mode and discharges the batteries for 25 seconds under the existing load.

S The batteries must be fully charged. S The bypass voltage must be acceptable. S No manual battery test was initiated previously in the same charging cycle. To pass the battery test, the battery voltage must remain above the threshold value during discharge.

Configuring Automatic Restart The UPS automatically restarts if utility returns after the output was shut off due to exhausted batteries, a shutdown input signal, or automatic shutdown command. The UPS supports two serial communication devices according to the following table:.

NOTE You can configure relays, signal inputs, and the serial port baud rate through the front panel menus see Table 3 on page See Figure 18 for the communication port locations. When the communication cable is installed, power management software can exchange data with the UPS. The software polls the UPS for detailed information on the status of the power environment.

If a power emergency occurs, the software initiates the saving of all data and an orderly shutdown of the equipment. The cable pins for the RS communication port are identified in Figure 19, and the pin functions are described in Table 4. Table 4. When the condition no longer exists, the output signal returns to Low.

Page 29 Align the mounting brackets with the screw holes on each side of the UPS and secure with the supplied M4 8 flat-head screws see Figure 6. Page 30 Repeat for any optional cabinets. Securing the Front of the Cabinet Rev 3 www. Page Rackmount Wiring Installation To remove the cover, remove and retain the two screws on the right side of the cover. Grasp the top and bottom of the cover and slide the cover to the right. Page 32 Clip the wires of the rightmost connector to the battery panel in its new position.

Connect red to red, and black to black. Press the two parts tightly together to ensure a proper connection. Page Connecting The Ebm S To remove the cover, remove and retain the two screws on the right side of the cover. Grasp the sides of the cover and slide the cover to the left and then away from the cabinet. See Figure 12 for the location of the EBM cable knockouts. Page 36 Verify that the EBM connections are tight and that adequate bend radius and strain relief exist for each cable.

Tower Installation The Eaton tower cabinet comes fully assembled and ready to connect. Do not pull on the cable or disconnect it. NOTE Leave ribbon cable connected. Figure Page 39 To replace the cover, verify that the ribbon cable is protected, then insert the clips on the back of the cover into the cabinet and push firmly to snap the cover into place. Verify that the EBM connections are tight and that adequate bend radius and strain relief exist for each cable.

Plug in EBM cable. Rotate clip. Reinstall cable retention clip. Connecting the EBMs Rev 3 www. Correct the alarms and restart if necessary. Page 43 UPS display. However, Eaton recommends that the batteries charge for 48 hours after installation or long-term storage. If optional EBMs are installed, see the recharge times listed in Table 25 on page Page Operation Chapter 4 Operation This chapter contains information on how to use the Eaton , including front panel operation, operating modes, UPS startup and shutdown, transferring the UPS between modes, retrieving the Event Log, setting the power strategy, and configuring bypass settings, load segments, and battery settings.

Page Changing The Language and to scroll through the menu structure. Press the Enter button to select an option. Press the button to cancel or return to the previous menu. Service Settings This menu is password-protected. What is the weight of the Eaton RM 2U? The Eaton RM 2U has a weight of g.

What certifications does the Eaton RM 2U have? What is the height of the Eaton RM 2U? The Eaton RM 2U has a height of 87 mm. What is the width of the Eaton RM 2U? The Eaton RM 2U has a width of mm.

What is the depth of the Eaton RM 2U? Remove and retain the two screws holding the battery cover plate. Grasp an edge of the battery cover plate and pull it forward gently. Replace the battery cover plate into the slots at left, threading the battery connector through the access slot. Reinstall the retained screws. Lifting the cabinet into the rack requires a minimum of two people. To replace the EBMs: 1. Remove the front cover of each EBM. To remove the cover, remove and retain the two screws on the right side of the cover.

If not already installed, install the supplied mounting brackets on the new EBM s. Page Replacing Tower Ebms For each cable retention clip removed, rotate the clip and install it under each EBM cable connection using the retained screws.

Verify that the EBM connections are tight and that adequate bend radius and strain relief exist for each cable. Testing New Batteries To test new batteries: 1. Do not dispose of the battery or batteries in a fire. Batteries may explode. Page Specifications Chapter 7 Specifications Model Specifications This section provides the following specifications: Communication options Model lists Weights and dimensions Electrical input and output Environmental and safety Battery Table 8.

Page 85 Table Page 87 Table Page 89 Table Page 91 Table Page 93 Table Page 95 Table Page 97 Table Receptacles in Load Segment 1 are shaded. Table 10 on page 76 lists the rackmount models. Table 11 on page 77 lists the tower models. Input and output components for each model are listed in Table 15 through Table 21 pages 80 through Page Troubleshooting Chapter 8 Troubleshooting The Eaton is designed for durable, automatic operation and also alerts you whenever potential operating problems may occur.

Usually the alarms shown by the control panel do not mean that the output power is affected. Instead, they are preventive alarms intended to alert the user.

Press any button on the front panel display to activate the menu options. Press the Enter button to display the list of conditions. Overtemperature The UPS internal temperature is too high or a fan has failed. The power cord is not connected correctly. Check the alarm condition and perform the applicable action to resolve the condition. If the alarm status changes, the alarm beeps again, overriding the previous alarm silencing.

This Guaranty does not cover any defects or damages caused by: a failure to properly store the Product before installation, including the charge of batteries no later than the date indicated on the packaging; Print page 1 Print document pages.

Rename the bookmark. Delete bookmark? Cancel Delete. Delete from my manuals?

❿


at

No comments:

Post a Comment

Subscribe to: Post Comments (Atom)

Coreldraw graphics suite x6 portable free free

Looking for: Coreldraw graphics suite x6 portable free free  Click here to DOWNLOAD     ❿   Coreldraw graphics suite x6 portable free f...